Thursday, April 16, 2015

Lenovo IdeaPad s400 Touch Wifi Problem Fix After Installing Window 8.1

Ok, Window 8.1 is I guess a better version. However, after upgrading, wifi stops working on my sister's lenovo ideapad s400 touch laptop. I tried to reinstall the whole window just to find out the problem caused by the driver. The Broadcom wireless adapter works fine under window 8 but not 8.1. For some reasons, driver does not work, it shows error "limited connection". How to fix it? well, I just have to search for the driver on Lenovo website. I went to lenovo website just to find out that the driver is not available for 64 bit. It's a feature and should be pre-implemented in window 8.1. So I had to go search for the web and finally found the driver I was looking for.
here is the link: https://drive.google.com/open?id=0B2aGUKMcMA9UNzRQWTVOX0tDalE&authuser=0

Friday, April 4, 2014

Troubleshoot PC Problem (No Boot, No Video)

PERFORM THESE STEPS before posting about POST/boot/no video problems!

Last response: January 10, 2014 6:50 PM in Systems
shortstuff has kindly granted me permission to continue support of this thread.
jsc


"No POST", "system won't boot", and "no video output" troubleshooting checklist

This checklist is a compilation of troubleshooting ideas from many forum members. It's very important to actually perform every step in the checklist if you want to effectively troubleshoot your problem.


1.Did you carefully read the motherboard owners manual?

2. Did you plug in the 4/8-pin CPU power connector located near the CPU socket? If the motherboard has 8 pins and your PSU only has 4 pins, you can use the 4-pin connector. The 4-pin connector USUALLY goes on the 4 pins located closest to the CPU. If the motherboard has an 8-pin connector with a cover over 4 pins, you can remove the cover and use an 8-pin plug if your power supply has one. This power connector provides power to the CPU. Your system has no chance of posting without this connector plugged in! Check your motherboard owners manual for more information about the CPU power connector. The CPU power connector is usually referred to as the "12v ATX" connector in the owners manual. This is easily the most common new-builder mistake.





3.Did you install the standoffs under the motherboard? Did you place them so they all align with the screw holes in the motherboard, with no extra standoffs touching the board in the wrong place? A standoff installed in the wrong place can cause a short and prevent the system from booting.




4.Did you verify that the video card is fully seated? (may require more force than a new builder expects.)

5.Did you attach ALL the required power connector(s) to the video card? (some need two, some need none, many need one.) It is best to use cables connected directly to the PSU. Only use adapters if absolutely necessary.




6.Have you tried booting with just one stick of RAM installed? (Try each stick of RAM individually in each RAM slot.) If you can get the system to boot with a single stick of RAM, you should enable an XMP profile or manually set the RAM speed, timings, and voltage to the manufacturers specs in the BIOS before attempting to boot with all sticks of RAM installed. If your motherboard supports XMP profiles that is the best way to get your RAM running at its rated specs.Nearly all motherboards default to the standard RAM voltage (1.8v for DDR2 & 1.5v for DDR3). If your RAM is rated to run at a voltage higher than the standard voltage, the motherboard will underclock the RAM for compatibility reasons. If you want the system to be stable and to run the RAM at its rated specs, you should either enable an XMP profile or manually set the values in the BIOS. Many boards don't supply the RAM with enough voltage when using "auto" settings which causes stability issues.

7.Did you verify that all memory modules are fully inserted? (may require more force than a new builder expects.) It's a good idea to install the RAM on the motherboard before it's in the case.

8.Did you verify in the owners manual that you're using the correct RAM slots? Many Intel motherboards require RAM to be installed in the slots starting with the one further away from the CPU.

9.Did you remove the plastic guard over the CPU socket? (this actually comes up occasionally.)



10.Did you install the CPU correctly? There will be an arrow on the CPU that needs to line up with an arrow on the motherboard CPU socket. There may also be a notch that will only line up in one direction. Be sure to pay special attention to that section of the manual!




11.Are there any bent pins on the motherboard/CPU? This especially applies if you tried to install the CPU with the plastic cover on or with the CPU facing the wrong direction.



12. If using an after market CPU cooler, did you get any thermal paste on the motherboard, CPU socket, or CPU pins? Did you use the smallest amount you could? Here's a few links that may help: 

Benchmark Reviews

Arctic Sliver

http://www.youtube.com/watch?v=ffK7L0Qj13Q&feature=rela...

13.Is the CPU fan plugged in? Some motherboards will not boot without detecting that the CPU fan is plugged in to prevent burning up the CPU.

o


14. If using a stock cooler, was the thermal material on the base of the cooler free of foreign material, and did you remove any protective covering? If the stock cooler has push-pins, did you ensure that all four pins snapped securely into place? (The easiest way to install the push-pins is outside the case sitting on a non-conductive surface like the motherboard box. Read the instructions! The push-pins have to be turned the OPPOSITE direction as the arrows for installation.)




15. Are any loose screws laying on the motherboard, or jammed against it? Are there any wires run directly under the motherboard? You should not run wires under the motherboard since the soldered wires on the underside of the motherboard can cut into the insulation on the wires and cause a short. Some cases have space to run wires on the back side of the motherboard tray.

16.Did you ensure you discharged all static electricity before touching any of your components? Computer components are very sensitive to static electricity. It takes much less voltage than you can see or feel to damage components. You should implement some best practices to reduce the probability of damaging components. These practices should include either wearing an anti-static wrist strap or always touching a metal part of the case with the power supply installed and plugged in, but NOT turned on. You should avoid building or working on a computer on carpet. Working on a smooth surface is the best if at all possible. You should also keep fluffy the cat, children, and fido away from computer components.

17.Did you install the system speaker (if provided) so you can check beep-codes in the manual? A system speaker is NOT the same as normal speakers that plug into the back of the motherboard. A system speaker plugs into a header on the motherboard that's usually located near the front panel connectors. The system speaker is a critical component when trying to troubleshoot system problems. You are flying blind without a system speaker. If your case or motherboard didn't come with a system speaker you can buy one for cheap here: http://www.cwc-group.com/casp.html



18.Did you read the instructions in the manual on how to properly connect the front panel plugs? (Power switch, power led, reset switch, HD activity led) Polarity does not matter with the power and reset switches. If power or drive activity LED's do not come on, reverse the connections. For troubleshooting purposes, disconnect the reset switch. If it's shorted, the machine either will not POST at all, or it will endlessly reboot. 




19.Did you turn on the power supply switch located on the back of the PSU? The switch should be depressed on the side with a I, the O means off. Is the power plug on a switch? If it is, is the switch turned on? Is there a GFI circuit on the plug-in? If there is, make sure it isn't tripped. You should also make sure the power cord isn't causing the problem. Try swapping it for a known good cord if you have one available.



20.Is your CPU supported by the BIOS revision installed on your motherboard? Most motherboards will post a CPU compatibility list on their website.

21.Have you tried resetting the CMOS? The motherboard manual will have instructions for your particular board.

http://www.spotht.com/2010/02/reset-bios-clear-cmos.htm...

22. If you have integrated video and a video card, try the integrated video port. Resetting the bios, can make it default back to the onboard video. If you are trying to use HDMI outputs, try using DVI or VGA instead. Sometimes the HDMI ports won't work until the correct drivers are installed.

23. Make certain all cables and components including RAM and expansion cards are tight within their sockets.


I also wanted to add some suggestions that jsc often posts. This is a direct quote from him:

"Pull everything except the CPU and HSF. Boot. You should hear a series of long single beeps indicating memory problems. Silence here indicates, in probable order, a bad PSU, motherboard, or CPU - or a bad installation where something is shorting and shutting down the PSU.

To eliminate the possiblility of a bad installation where something is shorting and shutting down the PSU, you will need to pull the motherboard out of the case and reassemble the components on an insulated surface. This is called "breadboarding" - from the 1920's homebrew radio days. I always breadboard a new or recycled build. It lets me test components before I go through the trouble of installing them in a case.

If you get the long beeps, add a stick of RAM. Boot. The beep pattern should change to one long and two or three short beeps. Silence indicates that the RAM is shorting out the PSU (very rare). Long single beeps indicates that the BIOS does not recognize the presence of the RAM.

If you get the one long and two or three short beeps, test the rest of the RAM. If good, install the video card and any needed power cables and plug in the monitor. If the video card is good, the system should successfully POST (one short beep, usually) and you will see the boot screen and messages.

Note - an inadequate PSU will cause a failure here or any step later.
Note - you do not need drives or a keyboard to successfully POST (generally a single short beep).

If you successfully POST, start plugging in the rest of the components, one at a time."


If you suspect the PSU is causing your problems, below are some suggestions by jsc for troubleshooting the PSU. Proceed with caution. I will not be held responsible if you get shocked or fry components.

"The best way to check the PSU is to swap it with a known good PSU of similar capacity. Brand new, out of the box, untested does not count as a known good PSU. PSU's, like all components, can be DOA.

Next best thing is to get (or borrow) a digital multimeter and check the PSU.

Yellow wires should be 12 volts. Red wires: +5 volts, orange wires: +3.3 volts, blue wire : -12 volts, violet wire: 5 volts always on. Tolerances are +/- 5% except for the -12 volts which is +/- 10%.

The gray wire is really important. It should go from 0 to +5 volts when you turn the PSU on with the case switch. CPU needs this signal to boot.

You can turn on the PSU by completely disconnecting the PSU and using a paperclip or jumper wire to short the green wire to one of the neighboring black wires.

http://www.youtube.com/watch?v=5FWXgQSokF4&feature=yout...

This checks the PSU under no load conditions, so it is not completely reliable. But if it can not pass this, it is dead. Then repeat the checks with the PSU plugged into the computer to put a load on the PSU. You can carefully probe the pins from the back of the main power connector."


Here's a link to jsc's breadboarding thread:

http://www.tomshardware.com/forum/262730-31-breadboardi...


If you make it through the entire checklist without success, Proximon has put together another great thread with a few more ideas here:

http://www.tomshardware.com/forum/264823-31-progess-tro...

Saturday, September 14, 2013

How To Fix Sudden Shutdown From Asus UX31E Laptop While on Battery Mode

*UPDATE: previous software fix didn't really fix the problem. Now going down to the hardware, the battery specifically.
After diagnosing the problem, it comes down to the battery connector to the mother board. For some reason the connector didn't attached very well to the pin. I tried to pull battery connector out, wait for about 1 minute, then plug it back in. And viola, I did not encounter the problem ever since. To be honest, never expect this hardware problem from Asus since it's a known brand for hardware. But I guess no brand is perfect.



Friday, August 16, 2013

How To Flesh-Install Window 8 from USB

Here's the steps I had to take to install Windows 8 on an ASUS Zenbook Prime UX31E
  1. download Windows 8 and instead of doing the in-place upgrade, save the file as an .iso
  2. mount the ISO using Virtual Clone Drive (or your favorite mounting tool)
  3. insert a 4GB USB drive & format it to FAT32 this is a very important part, and this is why the Microsoft USB/DVD tool does not work, as that awesome tool formats the USB drive as NTFS.
  4. copy all the files from the iso over to the flash drive, keeping the directory structure intact
  5. reboot and hit ESC when you see the ASUS logo to bring up the boot menu
  6. Look for and select the UEFI: Lexar yadda yadda yadda (your entry will vary based on the make of your USB drive) but the UEFI: part is critical
  7. install windows 8 "normally"
this is quick & dirty just to get you installed, maybe one day I'll refine it and add screen shots... but probably not :)

Tuesday, April 16, 2013

Fixing No-Folder Option On Right Click Context Menu (window 7)

There is no option to create new folder on context menu when right click on mouse. The problem is created by damaged or deleted registry key. 
Here is how to fix the problem: 
1. Click Start, type regedit in Search Bar, and then click regedit in the Programs list.

Note: If you are prompted for an administrator password or confirmation, type your password or click Continue.



2. Locate and then click the following registry subkey:



HKEY_CLASSES_ROOT\Directory\Background\shellex\ContextMenuHandlers\New\



3. Please check if the value for (Default) is: {D969A300-E7FF-11d0-A93B-00A0C90F2719}



If the issue persists after changing the registry key value, please continue to try the following suggestions:



1. Click Start, type regedit in Search Bar, and then click regedit in the Programs list.

Note: If you are prompted for an administrator password or confirmation, type your password or click Continue.



2. Locate and then click the following registry subkey:



HKEY_CLASSES_ROOT\Folder



3. Right click on the Folder key on the left pane, and then select "Export" to backup this registry key.

4. Download folderfix.zip file

5. Save the folderfix.zip file on to your Desktop.

<iframe src="https://skydrive.live.com/embed?cid=9DBB9DDA862DAB56&resid=9DBB9DDA862DAB56%21214&authkey=AOYH5OAhg4AZ3ms" width="98" height="120" frameborder="0" scrolling="no"></iframe>

6. Right click and extract the folderfix.reg file.

7. Right click on the folderfix.reg file and then click Merge.

8. Click Yes to confirm the modification.

Thursday, April 11, 2013

Recovery Admin Password using Offline Window NT Password Disk

I had earlier post about how to recover admin password using window 7 reset disk. This is the alternative to that method, and yet very powerful tool in case you lose the password, Offline window NT Password Disk.
Basically make download the source code from Here 
Then follow instruction on the screen
Note: make sure to go to the BIOS to enable USB boot if install on USB
You can watch this on youtube if you have no idea how to do it.





Friday, May 4, 2012

Fixing BIOS Damage

NOTE:
- Download the correct .exe installer from Dell's FTP site or Driver Site (Click on BIOS download->Other versions for older)
- Download Universal Extrator and install
- Run the first part of the Dell BIOS installer. It will extract 1645_AXX.exe, where XX is the bios revision, to a folder of your choice and open that folder.
- Right click on 1645_AXX.exe, and click on UniExtract to SubDir. Click on "Not an Installshield installer"
- It will open up your dos box and extract everything to a sub directory
- Navigate to 1645_AXX/.rsrc/1024/RCDATA/ and find the 5meg file, in the example case of 1645 bios A09, it's named 7000 with no file extension and weighs in at 5182 kb
* If the folder structure is different, then look around until you find any 4-6 meg file, that's the bios file.
- Rename it to BIOS.WPH and put this into your Crisis BIOS Recovery folder to replace the existing BIOS.WPH
- Run the BIOS Recovery tools as mentioned earlier in this thread. Success!

Another thing to note, if the recovery tools don't work for you by just plugging in the A/C and turning it on, take the battery out, stick in the USB to your USB/eSATA dual port, hold the END key, after 3 seconds plug in the A/C and release the END key. It should automatically turn on and use your usb stick to recover the bios. The circles on each side of the laptop will be orange if it's working. When it reboots after 2-3 minutes, take out the USB, let it boot to windows, shutdown, remove A/C, put in your battery, put in A/C, and boot up again and check your BIOS to see if the version is correct.

The only thing I'm not sure of is if this method actually flashes everything that needs to be flashed. I'm in no way a low level hardware guy. Is flashing the system BIOS the only thing Dell's installer does? I noticed the Dell update A09 notes say it updates a few other things, such as updating the SPI ROM EN25F32(BIOS) and the EN25F80(EC), but is that all inclusive in one simple BIOS.wph? I noticed there is a 1 meg file in the RCDATA folder, which is why I ask.
step to recovery bios:
step 1:create usb flash(download and run the WINCRIS.exe, and click "start")
step 2:remove the battery and unplug the power cable
step 3: plug in your usb into your laptop
step 4(important):hold down the key "End" in about 3 seconds and then plug the power cable at the same time release the key "End".
step 5: if you see the battery light is on with red, wait a few minute ...
If laptop is restart automatically, it means that the recovery is successful.